So I ssh'd the nas and saw that 2 usb storages where there.
This was not hard but not really reliable to have to press this button on every boot. voilà ! The nas was up with xpenology on it. after pre-install, I booted again the nas with backup button pressed and. So I started an installation on DSM 5.0 beta. no wait ! after 2 minutes, the nas showed up ! Pressing "enter" and then ran to my computer and starting Synology assistant. So I made usb boot key with trantor kernel and pluged it in the front usb port and a keyboard in the top back usb port.īooting with "backup" button pressed, well, this is not readynas os booting here, nothing on the lcd screen of the nas. Well It's possible to boot from external usb key however. but no vga (there is a vga header I beleive, but unsoldered) This little nas does have all the attributes of a standard computer. IMO, this is a fine piece of hardware, as it always is with netgear but the software, downside is pure crap.Īfter a first try with readynas OS 6.1.6 with has been ported to older hardware by community, I was steel unsatisfied, less but still crappy. Seeing it's really reliable I decided to build a home made nas with motherboard and disks, migrating data from my old netgeat readynas rndu 4000. I'm following for few month now this fantastic project, and it's time for me today to bring contribution.įor 3 months now, I'm testing xpenology both with trantor boot and gnoboot. Loading configuration from /etc/fancontrol. What should be the path to your fancontrol config file (/etc/fancontrol)? The fancontrol script can automatically respond to temperature changesĭo you want to set up its configuration file now (y)? Please verify that all fans have returned to their normal speed. There is either no fan connected to the output of hwmon2/pwm5, There is either no fan connected to the output of hwmon2/pwm3, The pwm outputs connected to the fan connectors,ĭid you see/hear a fan stopping during the above test (n)? Or the connected fan has no rpm-signal connected to one of There is either no fan connected to the output of hwmon2/pwm1, Would you like to generate a detailed correlation (y)? n If you do not want to do this hit control-C now!!! This may cause your processor temperature to rise!!! Warning!!! This program will stop your fans, one at a time, Hwmon2/fan2_input current speed: 2621 RPM Hwmon1/fan1_input current speed: 4635 RPM
Readynas fancontrol file full#
Giving the fans some time to reach full speed.
Hwmon2/pwm5 is currently setup for automatic speed control. Hwmon2/pwm4 is currently setup for automatic speed control. Hwmon2/pwm3 is currently setup for automatic speed control. Hwmon2/pwm2 is currently setup for automatic speed control.
Readynas fancontrol file manual#
You want to setup this output for manual control? (n) y It is more efficient and it reacts faster. In general, automatic mode is preferred over manual mode, as Hwmon1/pwm1 is currently setup for automatic speed control.
Physically verify that the fans have been to full speed However, it is ** very important ** that you The program will attempt to restore each fan to full speedĪfter testing. We will attempt to briefly stop each fan using the pwm controls.
Note that many motherboards do not have pwmĬircuitry installed, even if your sensor chip supports pwm. This program will search your sensors for pulse width modulation (pwm)Ĭontrols, and test each one to see if it controls a fan on Thank you for your time and ~]$ sudo pwmconfig So i tried my best do get fancontrol to work, but I just dont understand anything, below I copy pasted first my console, then the etc/fancontrol file that I thing did not get generated correctly, pls tell my what i should do different/now, to tell the fans when to start running and when to go full speed.
0 kommentar(er)
